Bulk Asphalt Tack Coat – (4) 250 Gallon Totes
- Fast-setting formula cuts downtime before the next coat
- One-component, ready-to-use—just spray and go
- DOT-grade SS-1h emulsion for overlays and patches
Free Shipping to commercial address with a dock or forkliftAvailability: In stock
Bulk Asphalt Tack Coat – 4 × 250-Gal Totes, SS-1h
Cover big jobs fast with 1,000 gallons of DOT-approved SS-1h tack coat in four forklift-ready totes. The water-based emulsion bites deep so your crew can pave sooner and keep profits moving.
Overview & Use Cases
Our bulk asphalt tack coat 250 gallon totes arrive ready to spray, saving time on every job.
- Pave overlays on highways, parking lots, and driveways
- Prime patches before infrared repair or pothole filling
- Speed large resurfacing contracts with fewer changeovers
Key Features & Benefits
- Pro-grade SS-1h emulsion – DOT-approved for dependable bond
- Penetrating surfactant package locks new asphalt to old and stops slippage
- Ready-to-use straight from the tote — no heating or thinning
- Low-VOC (< 10 g/L) & non-flammable for safer jobsites and easy compliance
- Bulk format means fewer refills and lower cost per lane-mile
Call an expert to lock in freight-optimized pricing today.
Application Instructions
- 1. Prep – Sweep and dry the surface; remove loose debris.
- 2. Mix – Spray full strength for patches; dilute 5:1 for fog or wash coats.
- 3. Apply – Spray 0.10 gal/yd² using a tack-coat sprayer.
- 4. Cure – Allow to dry (weather-dependent) before paving.
- 5. Clean-up – Flush lines and tips with water.
Need gear? Check out our Spray Systems for a plug-and-play pump setup.
Recommended Uses
- Prime pavement with a tack coat for asphalt overlay on highways, parking lots, and driveways
- Bond coat under infrared or saw-cut patches
- Large resurfacing jobs where 1,000 gallons keep crews productive
Patch first, spray tack, then finish with Asphalt Emulsion Sealer for a color-matched surface.
Storage & Handling
Store totes upright, out of direct sun, above 50 °F and below 120 °F; do not freeze.
- Keep lids tight to prevent skinning
- Avoid skin or eye contact; use standard PPE
- Dispose of rinse water in accordance with local regulations
Why Choose Bulk Asphalt Tack Coat
Buying four 250-gallon totes slashes downtime—no drum swaps, no partial loads. You get SS-1h performance, fast-setting turnaround, and low-VOC safety in a single shipment, backed by Asphalt Kingdom’s expert support and free jobsite troubleshooting.
Ready to pave faster and profit more? Click “Add to Cart” or call now to schedule delivery—and beat the next bid deadline with our bulk asphalt tack coat 250 gallon totes.
FAQs
| Questions | Answers |
|---|---|
| How do I pump and spray the bulk tack coat from a 250-gal tote? | Use a dedicated tack-coat sprayer or transfer pump; product can also be applied directly from a pour pot or other mechanized equipment. |
| Is Asphalt Tac SS-1h tack coat officially DOT-approved? | Yes. It meets DOT SS-1h specifications for emulsified asphalts. |
| What’s the recommended application rate? | Spray at roughly 0.10 gal per square yard over the prepared surface. |
| How long should I wait before paving over the tack coat? | It’s a fast-set emulsion—crews can usually resume paving within 15–30 minutes, although drying time depends on weather. |
| How should I store unused totes? | Keep totes sealed, out of direct sun, above 50 °F and below 120 °F. Never let the emulsion freeze. |
| Is the product hazardous or flammable? | It’s water-based, non-hazardous under EPA TCLP, and shows no tendency to flash or ignite when cured. VOC < 10 g/L. |
| Product Name | Asphalt-Tac™ SS-1h Tack Coat Emulsion |
| Composition | Water-based asphalt emulsion (SS-1h) |
| Compliance | Meets ASTM D977; DOT SS-1h |
| Unit Size | Bulk pack – four × 250-gal totes (1,000 gal total) |
| Color (dry) | Black |
| VOC Content | <10 g/L (<0.08 lb/gal) |
| Application Rate | 0.10 gal / yd² |
| Drying / Set Time | Fast-setting; actual time varies with weather |
| Non-Flammable | Cured product shows no tendency to ignite |
| Storage Temp. | Keep > 50 °F and < 120 °F; do not freeze |
| Cleanup | Water |
0
5 stars
0% (0)
4 stars
0% (0)
3 stars
0% (0)
2 stars
0% (0)
1 star
0% (0)
Share your thoughts with other customers
Top customer reviews
No reviews
