Preformed Thermoplastic Lane Reduction Arrow Left (18' x 5'8", Color Options)
Details
Specs
Reviews
Resources
Make it a Biz
FAQs
FREE SHIPPINGThis 1-piece, FHWA-style symbol installs with a propane torch for a bold, consistent marking. Choose Tuff-Mark Standard for a smooth finish, or upgrade to Tuff-Grip skid-resistant when traction matters in lane drops and tapers. Add optional surface glass beads for stronger night reflectivity.
- Earlier merge warning
- Less touch-up than paint
- Help drivers merge sooner, add grip or beads
Make Lane Drops Obvious, Keep Merges Predictable
The thermoplastic lane reduction arrow left is built for high-visibility merge guidance in taper zones and lane reductions. Since it is preformed and 1-piece, you spend less time laying out a long symbol and more time finishing the job.
Key Features & Benefits
- 18-foot symbol: big guidance drivers can recognize sooner
- 1-piece install: fewer alignment steps in long taper areas
- Durable thermoplastic: built for traffic wear in merge zones
- Optional glass beads: brighter at night under headlights
Choose Your Finish: Tuff-Mark Standard vs Tuff-Grip
- Tuff-Mark (Standard, smooth): a solid choice for typical lane drops and driving lanes
- Tuff-Grip (Skid-Resistant): adds traction where slip risk is higher, especially in wet conditions
For controlled bead coverage, consider a Reflective Glass Bead Dispenser.
How to Use
- 1. Surface prep: Sweep and blow off debris. Surface must be clean and dry.
- 2. Position: Align the symbol in the taper where drivers will see it early.
- 3. Torch apply: Heat evenly until bonded to the pavement.
- 4. Cool and reopen: Allow to cool and harden before traffic. Cooling is typically a few minutes. Cool water can speed it up.
Recommended Uses
- Left lane reductions and merge tapers
- Work zones and traffic pattern changes
- Commercial sites with lane drops and channelized flow
Need additional direction symbols for the same site? Add a Preformed Thermoplastic Straight Arrow (2 pcs) for long, clear lane guidance through extended approaches.
Storage & Handling
- Store indoors in a dry area.
- Recommended storage range is 35°F to 90°F.
- In colder conditions around 50°F and below, handle carefully to reduce cracking risk.
Why Choose This Lane Reduction Arrow
- Clear merge guidance that reduces confusion and complaints
- Faster installs than paint when you need consistent results
- Options for traction and reflectivity based on site needs
Add it to cart and make lane drops easier for drivers to understand.
| Product Type | Preformed Thermoplastic Lane Reduction Arrow (Left), FHWA style |
|---|---|
| Size | 18' x 5'8" |
| Pieces per Pack | 1 pc |
| Finish Options | Tuff-Mark Standard (smooth) or Tuff-Grip (skid-resistant) |
| Color Options | White, Yellow, Black, Blue, Bike Lane Green, Red, Orange, Purple |
| Optional Add-On | Surface glass beads (retroreflectivity) |
| Installation Method | Torch-applied |
| Traffic Re-Open | After cooling and hardening (typically a few minutes) |
| Storage | Store indoors, dry, 35°F–90°F recommended |
0
5 stars
0% (0)
4 stars
0% (0)
3 stars
0% (0)
2 stars
0% (0)
1 star
0% (0)
Share your thoughts with other customers
Top customer reviews
No reviews
Remove dust, sand, and loose aggregate using a broom or blower. The pavement must be clean and dry before torch application.
For standard asphalt installs, a separate primer is typically not required. For unusual surfaces or questionable pavement, follow your project requirements or contact support.
Once the marking cools and hardens. Cooling is typically only a few minutes. A light spray of cool water can speed up the cool-down.
Install on a clean, dry surface. In colder conditions around 50°F and below, handle carefully since the material can be less flexible.
Tuff-Mark is the standard smooth option for typical lanes and symbols. Tuff-Grip is the skid-resistant option, made to add traction where slip risk is higher.