100% airport grade and dries within hours! In stock and ready to ship to your door.
Save when buying a complete skid or more instead of 1 drum at a time! The property owner or contractor needs access to the asphalt surface as soon as possible after sealing. This asphalt emulsion sealer makes it possible.
The average drying time is 3 to 4 hours after application. That beats other emulsion sealers by at least 12 hours. It's possible to sealcoat in the morning and be open for business by the afternoon. Asphalt maintenance clients want that.
The competition's emulsion sealer takes approximately 24 to 48 hours to dry. Asphalt Kingdom's Sealer takes 3 to 4 hours to dry. When talking to potential customers, this is a significant sales advantage. It provides a major sales conversion edge.
That timing is not the only advantage over the competition when using Asphalt Kingdom's Sealcoating Sealer. This emulsion sealer is practical for business and delivers a higher quality seal for customers, who then become repeat clients.
This quality asphalt sealer can be sprayed with an AK Spray System, applied with a sealer brush, or added with a squeegee. That's high flexibility and perfect for businesses that are just starting out or transitioning to the next level.
A 55-gallon drum of sealer will do six to eight 4-car driveways. Its coverage rate is 100 square feet per gallon. With a skid, that's enough to do a small neighborhood or a small parking lot. Plus, the quality of this emulsion sealer will speak for itself when showing before and after photos.
*Please Note: Free shipping on our Sealer or Crack Filler does not apply to the following states: Washington, Oregon, California, Nevada, Arizona, Utah, Wyoming, Montana, Alaska, or Hawaii. Please contact us for the best shipping rates to your area at 1-866-399-5562.
We carry commercial-grade DOT spec sealer with a coverage rate of 100 square feet per gallon.
Temperatures must be 55 degrees or warmer for 3 hours after application for it to dry properly. Cure times will be longer in cooler conditions. The hotter it is, the faster the water evaporates from the sealer and the dry time can be as fast as 30 minutes. Try not to apply if hotter than 105°F.
Ideally sealer should dry for a couple of hours before it rains. It may need more time if it's very cloudy and humid.
There is no need for two coats, but if you're doing two coats, do them a week apart so the sealer has time to cure completely.
Asphalt is like a sponge which can only absorb so much sealer. Thicker isn't better if it doesn't get absorbed. We recommend between 25-30% dilution to get good even coverage at maximum efficiency.
The cause of this is over-agitating the sealer. Only recirculate your sealer for 2-3 minutes max at the beginning of the day and maybe for a minute at the beginning of each job.
You get this when the sealer is too thick and the pump cannot create a prime to circulate the sealer. Dilute it properly to achieve 20 to 30% water dilution.
Use a dipstick to check the level of your sealer at the end of the day and the next time you use your system, just in case of water evaporation (if the levels are different, add enough water to regain the previous sealer level).
Another possible reason could involve the system's ball valve. On the output part of the pump, there's a ball valve that allows you to redirect the sealer to the top of the tank or to the spray gun. If that ball valve is constantly or permanently broken to the spray gun, you wouldn't get recirculation.
It's best to always have a bucket of soap and water handy. If there are stains, try an orange based hand cleaner available at any auto parts store. Apply to the overspray and let it work in for several minutes before removing with soapy water. You ...
It comes down to your weight and convenience. Totes weigh a grand total of about 3,000 lbs. As it sits for periods of a week or longer, the sediment and the clay in the sealer will settle to the bottom leaving a thick sludge at the bottom of the tote...
Length | 48.0000 |
Width | 48.0000 |
Height | 48.0000 |
Shipping Weight | 2400 lbs |
Water % | 53 Max, 48 Min |
Non-Volatile % | 52 Max, 47 Min |
Ash % | 39 Max, 35 Min |
Sp. Gr. @ 77° | 1.29 Max, 1.19 Min |
Product Safety Data Sheet | Download here |